A gas dryer that spins but won’t ignite usually has a closed gas supply, a blown thermal fuse, a failed igniter, a weak flame sensor or gas valve coil, or a blocked vent. Check those in that order. If you smell gas at any point, stop, shut off the gas, open windows and call a licensed technician before touching anything else.
TL;DR:
- Watch the port: no glow points to a fuse or igniter, long glow suggests the flame sensor, and brief glow suggests failing valve coils.
- A typical igniter reads roughly 50 to 500 ohms; an open reading means failure, but valve coils can pass cold tests and fail under load.
- Clean the vent yearly, or sooner if drying times rise; a thermal fuse may fail again if you replace it without clearing a blockage.
- Leave live voltage tests, suspected sticking valves, and repeated fuse failures to a licensed technician; check CPSC.gov for recalls using your model number.
Table of Contents
- What can you check first when a gas dryer has no flame?
- How does the ignition chain work, and how do you test it?
- Could airflow and venting be stopping your dryer from lighting?
- How do you test the thermal fuse, thermostats and centrifugal switch?
- What is the safest step-by-step troubleshooting order?
- What parts might you need, and what do they cost?
- When should you stop and call a professional?
- What do technicians see most often, and what’s a good rule of thumb?
- How can we help when your gas dryer won’t light?
- FAQ
- Sources
What can you check first when a gas dryer has no flame?
Start with the quick rule-outs. They are quick, need no tools, and can resolve some no-heat problems.
- Open the gas shutoff valve. Look at the valve behind the dryer. The handle should sit parallel to the gas pipe for an open connection, according to Whirlpool’s product help. A handle turned across the pipe means the gas is off.
- Pick a heated cycle. Cycles like Air Only, Fluff or a cool-down setting turn heat off on purpose. Choose a high-heat timed cycle instead of an auto-dry setting.
- Run it long enough. Let the dryer run on high heat for a full five minutes before you decide anything is broken. The burner may cycle on and off, and early seconds can fool you.
- Check the breaker panel. A dryer needs the correct electrical supply for its model. If a breaker trips, the drum and lights can still work while the heating circuit stays dead. Flip the dryer breaker fully off, then back on.
- Look at the lint screen and the outside vent. A clogged screen or a flap that doesn’t open can shut down heat. We cover that in detail below.
- Smell the room. If you notice gas, stop using the dryer, close the gas valve, ventilate and call a professional.
Run a heated cycle for at least five minutes before concluding there is a technical failure. Whirlpool’s guidance is to confirm the valve is open and a true heat setting is selected first, which rules out two simple causes.
If none of that restores flame, move on to the ignition chain. Our five quick checks for a dryer that won’t heat also walks through airflow-first fixes that overlap with this list.
How does the ignition chain work, and how do you test it?
A modern gas dryer lights through a sequence of safety steps. The igniter, often called a glo-bar, heats up. The sensor detects that heat and tells the gas valve to open. Gas flows, ignites, and the igniter shuts off once the flame is established, as GE Appliances explains. If any link fails to reach its “ready” state, the dryer blocks gas flow on purpose. That is a safety design, not a glitch, as iFixit’s troubleshooting guide points out.
You can learn a lot just by watching. Most dryers have a small observation port near the bottom front of the cabinet. Run a high-heat timed cycle and look through it with a flashlight. Then match what you see to the likely fault:
- No glow at all: iFixit ties this to the thermal fuse or the igniter itself.
- Long glow, no flame: this points toward a bad flame sensor.
- Short glow, then off, no flame: this suggests the gas valve solenoid coils are failing.
- Glow, flame, then the burner shuts off early: look at airflow and the thermostats, covered below.
For cold testing, unplug the dryer first. Whirlpool’s technical sheet for a gas model, hosted on ManualsLib, describes measuring igniter and gas valve coil resistance with an ohmmeter and comparing the reading to the manufacturer’s range. It lists a typical acceptable igniter range of roughly 50–500 ohms. A reading of infinite resistance means the igniter is open and needs replacing. The same manual also has you check flame sensor continuity.
Pro Tip: A coil that reads normal on a cold ohm test can still fail once it heats up under voltage, so if your igniter glows briefly and the burner never lights, replace the coil set instead of trusting the meter.
Could airflow and venting be stopping your dryer from lighting?
Yes. Restricted airflow makes the heater box run hot, and thermal safety devices respond by cutting heat. The Energy Department’s NFPA fact sheet notes that restricted exhaust venting can raise heater-box temperatures substantially and increase fire risk. A blocked vent is also one of the most common reasons a thermal fuse blows again right after replacement.
Watch for these signs of an airflow problem: clothes take unusually long to dry, the top of the dryer or the laundry feels unusually hot, a burning smell shows up, or the vent hood outside barely moves when the dryer runs.
Work through this sequence:
- Pull out the lint screen and clean it. Wash it with warm water and a soft brush if it feels coated or stiff, since fabric softener leaves a film that blocks airflow.
- Reach into the lint screen slot with a flashlight and look for packed lint.
- Pull the dryer away from the wall and check that the transition duct is not crushed or kinked.
- Disconnect the vent from the dryer and run a short timed cycle. You should feel strong airflow at the dryer’s exhaust outlet.
- Go outside and check the vent hood. The flap should open freely when the dryer runs and fall closed when it stops. Lint or a nest can pin it shut. If birds keep getting in, see our guide on technician-tested dryer vent bird guards.
Safety guidance from NFPA and the Energy Department recommends cleaning the vent at least once a year, or sooner if drying times increase. That advice appears in their dryer and washer safety tips, which also recommends rigid or flexible metal venting rather than plastic or foil.
You can clean a short, straight duct yourself with a brush kit. A long run, a vent that exits through the roof, or a duct that goes through a second floor is better handled by a vent cleaning service. Our dryer vent cleaning frequency guide explains how often most households need it.
How do you test the thermal fuse, thermostats and centrifugal switch?
Unplug the dryer before you open any panel. These parts form the safety circuit that feeds power to the igniter, so one open part can mean no glow and no flame.
- Thermal fuse or thermal cutoff: this small part usually sits on or near the exhaust housing or the heater box. Pull the wires off and set your multimeter to continuity. A good fuse beeps. No continuity means it blew, and iFixit lists it as a cause of no igniter glow.
- Cycling thermostat: it opens and closes to hold the drum at temperature. If it sticks open, the dryer won’t heat. Test it for continuity at room temperature; a good one should show a closed path.
- High-limit thermostat: it trips when temperatures climb too high. An open reading on a cool dryer means the part has failed.
- Motor centrifugal switch: once the motor reaches speed, this switch sends line voltage onward to the ignition circuit. If it fails, the drum may spin normally while the igniter never gets power.
A fuse that tests open did not fail for no reason. Replacing it without fixing a clogged vent usually buys you one more cycle before it blows again, as iFixit’s guide warns.
What is the safest step-by-step troubleshooting order?
Gather a multimeter, insulated gloves, a nut driver set, a flashlight and a vacuum. Then follow this order so you never skip a safety step.
- Prep. Unplug the dryer and close the gas shutoff valve. Open a window or run a fan.
- Record the symptom. With the gas on and the dryer plugged in, run a high-heat timed cycle briefly and watch the igniter through the port. Write down whether it glows, how long, and whether a flame appears.
- Shut it down again. Close the gas valve and unplug the dryer before you open the cabinet.
- Test the thermal fuse first. It is cheap, easy to reach and a frequent culprit.
- Measure the igniter. Compare your reading with the manufacturer’s range, which the Whirlpool sheet gives as roughly 50–500 ohms for a typical igniter.
- Check the flame sensor. Test it for continuity per your model’s service sheet.
- Measure the gas valve coils. Compare each coil’s resistance to your model’s listed range.
- Replace what failed. An open reading means replace the part. If readings look normal but the behavior fits a failing coil, replace the set because cold tests can miss load failures.
- Reassemble, restore gas and power, and retest. Run a heated cycle and check for flame and heat.
Pro Tip: Photograph every wire connection before you pull anything, and label the two coil connectors, since mixed-up wiring on a gas valve is an easy mistake to make.
Stop and call a technician if you smell gas at any step, if you are asked to test live voltage and don’t feel comfortable doing it, or if the thermal fuse blows repeatedly.
What parts might you need, and what do they cost?
Most ignition repairs come down to a short list of parts:
- Igniter: the most common failure in a no-flame dryer, and usually an inexpensive part.
- Flame or radiant sensor: another low-cost part, though it sits close to the burner and needs careful removal.
- Gas valve coil kit: a bundled set of solenoid coils, usually priced well below a full valve.
- Thermal fuse or thermal cutoff: one of the cheapest parts in the dryer.
- Cycling thermostat: inexpensive, but access varies by model.
Parts are only half the picture. Labor, access and diagnosis time are where costs vary, because a valve, a control board or a wiring fault takes proper tools and gas-safety checks to confirm. If vent blockage or gas-line concerns turn up, a vent cleaning or gas-line inspection adds a step, but it is worth it when airflow or safety is in question. Our repair-or-replace test for dryers helps if the unit is old and you’re weighing a new one.
When should you stop and call a professional?
Some signs mean the job is no longer a DIY one.
- You smell gas, hear a hiss, or see scorch marks. Stop the dryer, shut off the gas, ventilate and call a licensed technician. The Consumer Product Safety Commission has long urged professional inspection of fuel-burning appliances to catch gas leaks, carbon monoxide and blocked vents, as in its seasonal inspection advisory.
- The valve may be sticking. If the burner runs on after the dryer shuts off, or gas seems to flow when it shouldn’t, stop using the machine.
- Parts keep failing. Repeated thermal fuse blowouts, coils that behave intermittently, or control board relay problems need a pro diagnosis.
- Your model has been recalled. The CPSC announced a repair program for certain gas dryers whose valves could fail to shut off, and told owners to stop using affected units until they were inspected or repaired, per its LG and Sears recall notice. Search your model number on CPSC.gov.
A professional visit also covers things a parts swap misses: vent integrity, gas-line connections and carbon monoxide risk. Our six signs your dryer is a fire risk lists other warning signs worth knowing.
What do technicians see most often, and what’s a good rule of thumb?
Most no-heat dryers we see don’t have an exotic problem. Airflow and a blown thermal fuse come first, and the two are often connected: a packed vent cooks the fuse. The gas valve and its coils are the part homeowners underestimate, because the failure looks like a dead igniter but the fix lives inside the gas train.
Here is the rule we give people: do the outside checks yourself. Check the shutoff, the settings, the breaker, the lint screen and the vent. The moment a fix needs live-voltage testing, gas valve work, or a second replacement of the same part, schedule a visit. Clean lint after every load and check the vent hood each season, and you’ll see far fewer repeat calls.
— Rich
How can we help when your gas dryer won’t light?
When the quick checks don’t bring back the flame, we can take it from there. We offer in-home dryer repair and dryer vent cleaning, and we stand behind our work with a warranty on parts and labor.
- Call us for any gas smell, a suspected valve or coil failure, or a thermal fuse that keeps blowing.
- Your visit starts with a diagnosis, then a clear quote, then the repair, so you know the cost before we replace anything.
- If the vent is the root cause, we can clean it.
You can schedule service online and get a technician to check the ignition chain safely, without the guesswork.
FAQ
Why did my gas dryer stop working?
The most common reasons are a closed gas valve, a blown thermal fuse, a failed igniter or a clogged vent. Check the shutoff valve, the heat setting and the breaker first, then look at airflow. If the drum spins but there is no flame, the fault is usually in the ignition chain.
Where is the thermal fuse located in a Kenmore gas dryer?
On most gas dryers, including many Kenmore models, the thermal fuse sits on or near the exhaust housing or the heater box. The exact spot varies by model, so check your service sheet. Unplug the dryer and close the gas valve before you open any panel.
Do you have to ignite a gas dryer?
No, you don’t light it by hand. A glo-bar igniter heats up, the sensor tells the gas valve to open, and the gas ignites on its own, as GE Appliances describes. If you ever see someone lighting one manually, stop and call a technician.
How do you test a gas dryer igniter?
Unplug the dryer, close the gas valve and set a multimeter to ohms. A typical igniter reads roughly 50–500 ohms, according to the Whirlpool technical sheet. An open reading means the igniter has failed and needs replacing.
Sources
- Not Heating – Gas Dryer – Product Help | Whirlpool
- Gas Dryer Not Heating – iFixit Troubleshooting
- Whirlpool WED94HEXW1 Technical Sheet (Page 17 of 56) | ManualsLib
- Cpsc